Industrial Parts Washers
WARRANTY AND POST-WARRANTY SERVICE
Industrial Parts Washers – solvent or aqueous Vacuum Water Washers
VACUUM-CAST 3000
Precision Parts Washing System
Whole installation works under vacuum. All possible ways of washing (immersion, spraying, ultrasound) are held in a vacuum. This increases the security of the entire process and prevent accidental opening of the working chamber and improves the quality of the cleaning bath by continuous degassing (especially important when ultrasound).
Vacuum evaporators for waste water
AQUADEST-CAST 3000
Washing Medium Distillation
Waste water for distillation goes firstly to heaters through heat exchanger where is preliminary heated-up. Waste water fills the heater, boiler and condenser. Roots vacuum pump sucks the water vapour which is over the liquid level in a boiler. Next, the pump compresses the water and heats it up simultaneously. Hot water vapour is directed to condenser where it is condensed and heats the bath in a boiler simultaneously. Clean water is directed to a tank for distillate.
Parts cleaning is essential to many industrial processes, as a prelude to surface finishing or to protect sensitive components
-Industrial Parts Washers-
Pro-ecological, vacuum destiller for waste solvents
VACUUM-DEST 3000
Washing medium distillation
The rising cost of wastewater treatment in biological wastewater treatment require more and newer technologies. Our company meet customer expectations has developed several solutions to effectively address this issue. Most effective and most energy-efficient systems are systems in vacuum distillation. Vacuum is used to lower the boiling point of liquid distilled at 25 mbar in the case of high-boiling solvents increases safety, reduces the time and encapsulates the process.
Solvent Based Vacuum Assisted Cleaning & Degreasing machines
ULT.DP-CAST
Vacuum Cleaning & Degreasing Systems
Meeting the expectations of customers, having extensive experience with the use of chlorinated solvents and low boiling companies 3M and DuPont, recently launched an innovative single-chamber washing system using ultrasound ULT.DP-CAST (patent No. 390 043 of 28.12.2009) with the following characteristics:
- Ultrasonic cleaning system
washers are equipped with modern ultrasound generators with digital tuning for maximum power in a continuous manner, by Weber Ultrasonics GmbH.
Ultrasonic Washers
ULT-CAST
Ultrasonic Cleaning Systems
Our Ultrasonic Parts Washers use modern generators and transducers provided by the German company, Weber Ultrasonics GmbH. Both the frequency and the power of the ultrasound are selected individually for each project. We provide the following frequency spectrum:
- from 25 kHz – strong cavitation,
- up to 1000 kHz – high washing precision.
The size of the tubs, process parameters, washing agent type and technology may be selected individually depending on the customer’s needs.
Multi-bath Ultrasonic Washers
ULT-CAST/CL
Ultrasonic Cleaning Systems
Featuring multi ultrasound washing lines – are designed to clean parts and recycling water. Closed loop washing bath, filtration, continuous distillation unit AQUADEST-CAST 3000 you can:
- maintain a reproducible purity of the cleaning process;
- extend the life of the bath and thus reduce the costs associated with disposal of waste machining.
Through the use of automation of the process driven, SIEMENS OP7 operator panel, Equipped with a microprocessor PLC, Increased efficiency washer, Reducing cleaning time details.
Ultrasonic and Spray Parts Washers – Hybrid
ULT SPRAY-CAST
Washing and degreasing of parts
Ecological ultrasonic-spray washers come in different versions:
- with rotating basket and a fixed shower or fixed basket and rotating basket;
- details can be loaded from the top or the face wash;
- washes are designed by individual arrangements taking into account the shape, size, type of detail, degree and type of contamination;
- have very high performance and efficiency details by ultrasonic cleaning, properly chosen chemistry;
- while bathing medium subject to constant washing of regeneration through filtration and separation of the oil;
- whole installation is made of stainless steel;
- automatic control based on Siemens controllers, or other as agreed with the customer.
Tunnel – Cycle Washers
SPRAYING-CAST 3001
Spray Cleaning Systems
The industrial washing machines (3001 series) have been designed for automatic work, with a complete monitoring of washing parameters such as: cycle, temperature in particular zones and liquids concentrations. Recycling of washing medium is especially recommended for continuous work with high cleaning quality demand washing.
Tunnel Washers
SPRAYING-CAST 3000
Spray Cleaning Systems
Zones: pre-washing, main washing, rinsing with deionised water, maintenance, corrosion, phosphating, drying (washing lines can be extended to other areas, depending on customer needs).Tunnel Washer SPRAYING-CAST 3000 are designed for automatic operation mode, with full control parameters, cleaning, drying and recycling of cleaning medium, particularly suitable for continuous operation with high efficiency and high quality cleaning requirements. Standard washers are equipped with continuous filtration cleaning medium can be used with optional continuous vacuum system VACUUM-DEST.
Gantry Spray Washers
SPRAY-CAST 3003
Spray Cleaning Systems
The installation was designed as a type of spraying washin machine, with front loading, for washing large-size and heavy (ton, tons) details. It may be used in the process of details production, e.g. made of stainless steel with many blind or open holes. It may also be applied when, repairing large-size chassis of carriage, mechanical coal miners, heavy-duty military and building industry equipment. The subassemblies applied in the machine are produced by renowned European firms.
Front Load Spray Washers
SPRAY-CAST 3003
Spray Cleaning Systems
Spray Parts Washers can operate in semi-automatic or fully automatic mode with the control of the most important work and technological processes.
Top Loading Spray Washers
SPRAY-CAST 3002
Spray Cleaning Systems
SPRAY-CAST 3002 is a spray parts washer water to cleaning and degreasing parts with different shapes and sizes. The washing process consists of spraying the surface of the medium myjącegona details. Maintenance of process conditions (among others. Pressure and medium flow) is possible by using components with high quality, reputable manufacturers. It is a guarantee of obtaining high purity washed surface detail.
.
Spray Washers with horizontal rotating basket
SPRAY-CAST 3004
Spray Cleaning Systems
SPRAY-CAST 3004 – They are dedicated to washing industrial parts:
- great number of fine components,
- blind holes where water deposits,
- specific geometry of components.
Thanks to the application of this washing method, the duration of the most energy-consuming process, i.e. hot air drying, can be reduced. The drying process cost can be dramatically cut, even as much as by half!
Additional Products
WEBER ULTRASONICS
The cleaning effect of ultrasound is based on the physical principle of cavitation. Here, the ultrasonic generator emits electrical signals at a certain frequency, which are then transferred to the cleaning liquid as ultrasonic waves via a rod-style or plate transducer. The sonic pressure is characterised by an interplay of positive and negative pressure (vacuum). As a result of the high intensity, microscopic bubbles form in the vacuum phases, which then implode in the subsequent overpressure phase, releasing local shock waves with considerable energy densities. In turn this triggers microflows in the liquid, which separate and clean away films and particulate matter from the components to be cleaned.
Additional Products
Ecological ultrasonic-spray washers come in different versions:
- Technological baskets;
- Transport and loadings systems
THE CONSTRUCTION OF THE WASHING MACHINES MEET EUROPEAN UNION REGULATIONS – MACHINERY DIRECTIVE 2006/42/WE
Questionnaire
Product Catalog
YOUTUBE
